Welcome, Guest. Please Login
SLINGING.ORG
 
Home Help Search Login


Page Index Toggle Pages: 1
Send Topic Print
Hello from Indiana University (Read 1580 times)
Jacob
Novicius
*
Offline


Slinging Rocks!

Posts: 2
Hello from Indiana University
Oct 3rd, 2010 at 4:12pm
 
Hello Everyone!

I made my first sling about a year ago using instructions from this site. I just made a new sling because my old one was getting really fuzzy because I made it from really unravelly twine. I've read through some of the site for advice and find it very interesting, and now I've decided to join.

I'm at Indiana University; anyone else from there?
Back to top
 
 
IP Logged
 
Aussie
Past Moderator
*
Offline


Joined Nov. 1, 2006  Luke
14:14

Posts: 3265
Melbourne, Australia
Gender: male
Re: Hello from Indiana University
Reply #1 - Oct 3rd, 2010 at 5:32pm
 
Greetings from Australia,

Welcome to the site. Somewhat distant from Indiana but that's the wonder of internet. Got your PM and will be forwarding pouches today. With good cords and used with tennis balls they'll last indefinitely.

What are you studying at uni?

Regards,

Aussie
Back to top
 

Cranks are little things that make revolutions.&&
 
IP Logged
 
Jacob
Novicius
*
Offline


Slinging Rocks!

Posts: 2
Re: Hello from Indiana University
Reply #2 - Oct 3rd, 2010 at 7:38pm
 
Thanks Aussie,

I'm studying Geology. I'm only in first year, though, so nothing is set in stone.

What sort of cord would you recommend using? I have some stuff that I believe is similar to paracord, although it is very slippery and flattened, instead of round. Knots have to be pulled very tight to stay tied.

Thanks Again,

Jacob
Back to top
 
 
IP Logged
 
Aussie
Past Moderator
*
Offline


Joined Nov. 1, 2006  Luke
14:14

Posts: 3265
Melbourne, Australia
Gender: male
Re: Hello from Indiana University
Reply #3 - Oct 4th, 2010 at 12:14am
 
Something a bit perversely amusing about a geology student slinging rocks. I wonder if any geologists have come across a stone thrown by some long gone slinger and wondered, "Strange, I wouldn't expect to find this particular stone here, it's quite out of place." Cheesy

Back to more relevant things. Paracord is very good, especially the milspec. 550 stuff as the quality and consistency is tops. However any quality braided synthetic cord will be fine. Motor mower pullstart cord is very good, strong, abrasion resistant and non stretchy. On the negative, it's a little difficult to tie and is a bit hard on your fingers. There's a very good cord available here that's sold as load tiedown cord. It's white with a single red thread through it, sold in Australia as Zenith brand. As all this material is made in China nowdays I'm sure it will be available in the US too. The only cord to avoid is the common twisted polypropylene type as it is impossible to tie, very hard on the hands and kinks badly.

Anoher possibilty is thin cotton sash cord. Rat Man uses this type of cord on his slings. I have one of his and one other of the same cord. Both very good. Downside of all white cords is that they don't stay white for long.
Back to top
 

Cranks are little things that make revolutions.&&
 
IP Logged
 
Redbeard
Junior Member
**
Offline



Posts: 79
Re: Hello from Indiana University
Reply #4 - Oct 4th, 2010 at 3:20pm
 
Jacob wrote on Oct 3rd, 2010 at 7:38pm:
I'm studying Geology. I'm only in first year, though, so nothing is set in stone.

Hahaha, "set in stone"... 
Back to top
 
 
IP Logged
 
Page Index Toggle Pages: 1
Send Topic Print
(Moderators: Bill Skinner, David Morningstar, Chris, Masiakasaurus, Mauro Fiorentini, Rat Man, Curious Aardvark)