Slinging.org Forum
https://slinging.org/forum/YaBB.pl
General >> General Slinging Discussion >> Repairing end of release cord
https://slinging.org/forum/YaBB.pl?num=1689146692

Message started by Yfir on Jul 12th, 2023 at 3:24am

Title: Repairing end of release cord
Post by Yfir on Jul 12th, 2023 at 3:24am
I'm a big fan of natural materials, so my slings often don't last long. Particularly the ends of the release cords - the end knot and loose string that gives it a nice whipping sound. I've tried repairing the ends by splicing in new string to replace the old, though after short use the spliced string unexpectedly comes undone while i'm slinging.

Anyone have any advice on how to effectively repair the end of the release cord?

Title: Re: Repairing end of retention cord
Post by Eino on Jul 12th, 2023 at 11:04am
You could try splicing in the new fiber over a longer distance, and gradually switch out the old fiber for new in each strand of the braid. That way the splice is not as abrupt and prone to weakness. If you are already doing this, the next step would be to put glue over the splice like in Archaic Arms' balearic sling tutorial (https://youtu.be/NRzGbu7Bvfo?t=1714).

If you want the retention release cord to last longer, use synthetic material for the very end, as it does not deteriorate as fast as natural fibers.

Title: Re: Repairing end of retention cord
Post by Yfir on Jul 13th, 2023 at 3:11am
Thanks Eino, i'll give that a try. Previously i concentrated the splices all in one area and that came undone quickly, so hopefully spreading them out will help.

Title: Re: Repairing end of retention cord
Post by Rat Man on Jul 13th, 2023 at 7:16am
I believe you mean the release cord.

Title: Re: Repairing end of retention cord
Post by Eino on Jul 13th, 2023 at 3:37pm

Rat Man wrote on Jul 13th, 2023 at 7:16am:
I believe you mean the release cord.

Yeah... oops :)

Title: Re: Repairing end of retention cord
Post by Yfir on Jul 13th, 2023 at 6:26pm
Damn! How could I make such an obvious mistake  :o

Thanks for pointing that out Rat Man, i'll edit the post.

Title: Re: Repairing end of release cord
Post by IronGoober on Jul 13th, 2023 at 8:35pm
@Yfir

I also really like natural slings...but when it comes to the release cord end/cracker, go synthetic. It will just last so much longer. I splice in polypropylene, nylon, polyester, kevlar or dyneema. Whatever you have that is plastic should work.

Here is how Luis Pons Livermore repairs his.
https://youtu.be/Z5n_N0yyLkQ

Here is how I repair sisal slings, but I usually have a tab, not a cracker on the end of these, so it lasts much longer.
To do this effectively, you have to undo a few inches of braid so that the new material becomes locked in. If you don't go back far enough, it will just pull out.
https://youtu.be/tzaYGOHDzjM

You can also see AA's video on adding dyneema to a balearic sling cracker.
https://youtu.be/NRzGbu7Bvfo?t=1480

Title: Re: Repairing end of release cord
Post by Yfir on Jul 14th, 2023 at 2:51am
Thanks Iron. They look like good, sturdy ways of repairing the cord, I'll keep them in mind next time I need to make a repair.

I know synthetics last much longer, but I just far prefer natural materials even for the end. Maybe I'll try waxing some of the string on the end and see if that helps with durability.

Title: Re: Repairing end of release cord
Post by JudoP on Jul 14th, 2023 at 6:20am
You could also go for the method of terminating the release cord in a loop and then installing easily replaceable twisted sling tails/crackers in (ala Jaegoor). This would at least make the replacement/repair step much easier.

In terms of natural materials that I've used, sisal is the one that has lasted the longest in release tassels. However even run of the mill nylon will easily outlive it. You could perhaps look into horsehair too?

In terms of sling design, making the end of the release cord a little thicker or stiffer will usually inhibit cracking whilst maintaining a 'whippy' release and as a bonus will probably be more resilient just by being thicker or higher braid count.

Title: Re: Repairing end of release cord
Post by Yfir on Jul 15th, 2023 at 4:28am

JudoP wrote on Jul 14th, 2023 at 6:20am:
You could also go for the method of terminating the release cord in a loop and then installing easily replaceable twisted sling tails/crackers in


I might look into that, thanks!

I've given horsehair a bit of a try, though it's pretty slippery and hard to work with. Plus it doesn't produce such a prominent whip sound, though maybe that's because I didn't put much in. Might give it another try and put more in, it's pretty expensive though.

Slinging.org Forum » Powered by YaBB 2.5.2!
YaBB Forum Software © 2000-2026. All Rights Reserved.